Share to: share facebook share twitter share wa share telegram print page

 

Luminous efficacy

Luminous efficacy
Common symbols
K
SI unitlm⋅W−1
In SI base unitscd⋅s3⋅kg−1⋅m−2
Dimension

Luminous efficacy is a measure of how well a light source produces visible light. It is the ratio of luminous flux to power, measured in lumens per watt in the International System of Units (SI). Depending on context, the power can be either the radiant flux of the source's output, or it can be the total power (electric power, chemical energy, or others) consumed by the source.[1][2][3] Which sense of the term is intended must usually be inferred from the context, and is sometimes unclear. The former sense is sometimes called luminous efficacy of radiation,[4] and the latter luminous efficacy of a light source[5] or overall luminous efficacy.[6][7]

Not all wavelengths of light are equally visible, or equally effective at stimulating human vision, due to the spectral sensitivity of the human eye; radiation in the infrared and ultraviolet parts of the spectrum is useless for illumination. The luminous efficacy of a source is the product of how well it converts energy to electromagnetic radiation, and how well the emitted radiation is detected by the human eye.

Efficacy and efficiency

Luminous efficacy can be normalized by the maximum possible luminous efficacy to a dimensionless quantity called luminous efficiency. The distinction between efficacy and efficiency is not always carefully maintained in published sources, so it is not uncommon to see "efficiencies" expressed in lumens per watt, or "efficacies" expressed as a percentage.

Luminous efficacy of radiation

By definition, light outside the visible spectrum cannot be seen by the standard human vision system, and therefore does not contribute to, and indeed can subtract from, luminous efficacy.

Explanation

The typical response of human vision to light under daytime or bright conditions, as standardized by the CIE in 1924. The horizontal axis is wavelength in nanometers.[8]

Luminous efficacy of radiation measures the fraction of electromagnetic power which is useful for lighting. It is obtained by dividing the luminous flux by the radiant flux.[4] Light wavelengths outside the visible spectrum reduce luminous efficacy, because they contribute to the radiant flux, while the luminous flux of such light is zero. Wavelengths near the peak of the eye's response contribute more strongly than those near the edges.

Wavelengths of light outside of the visible spectrum are not useful for general illumination[note 1]. Furthermore, human vision responds more to some wavelengths of light than others. This response of the eye is represented by the luminous efficiency function. This is a standardized function representing photopic vision, which models the response of the eye's cone cells, that are active under typical daylight conditions. A separate curve can be defined for dark/night conditions, modeling the response of rod cells without cones, known as scotopic vision. (Mesopic vision describes the transition zone in dim conditions, between photopic and scotopic, where both cones and rods are active.)

Photopic luminous efficacy of radiation has a maximum possible value of 683.002 lm/W, for the case of monochromatic light at a wavelength of 555 nm  .[note 2] Scotopic luminous efficacy of radiation reaches a maximum of 1700 lm/W for monochromatic light at a wavelength of 507 nm.[note 3]

Mathematical definition

Luminous efficacy (of radiation), denoted K, is defined as[4]

where

Examples

Photopic vision

Type Luminous efficacy
of radiation (lm/W) 		Luminous
efficiency[note 4]
Tungsten light bulb, typical, 2800 K 15[9] 2%
Class M star (Antares, Betelgeuse), 3300 K 30 4%
Black body, 4000 K, ideal 54.7[note 5] 8%
Class G star (Sun, Capella), 5800 K 93[9] 13.6%
Black-body, 7000 K, ideal 95[note 5] 14%
Black-body, 5800 K, truncated to 400–700 nm (ideal "white" source)[note 6] 251[9][note 7][10] 37%
Black-body, 5800 K, truncated to ≥ 2% photopic sensitivity range[note 8] 292[10] 43%
Black-body, 2800 K, truncated to ≥ 2% photopic sensitivity range[note 8] 299[10] 44%
Black-body, 2800 K, truncated to ≥ 5% photopic sensitivity range[note 9] 343[10] 50%
Black-body, 5800 K, truncated to ≥ 5% photopic sensitivity range[note 9] 348[10] 51%
Monochromatic source at 540 THz 683 (exact) 99.9997%
Ideal monochromatic source: 555 nm (in air) 683.002[11] 100%

Scotopic vision

Type Luminous efficacy

of radiation (lm/W)

Luminous

efficiency[note 4]

Ideal monochromatic 507 nm source 1699[12] or 1700[13] 100%
Spectral radiance of a black body. Energy outside the visible wavelength range (~380–750 nm, shown by grey dotted lines) reduces the luminous efficiency.

Lighting efficiency

Main article: Wall-plug efficiency

Artificial light sources are usually evaluated in terms of luminous efficacy of the source, also sometimes called wall-plug efficacy. This is the ratio between the total luminous flux emitted by a device and the total amount of input power (electrical, etc.) it consumes. The luminous efficacy of the source is a measure of the efficiency of the device with the output adjusted to account for the spectral response curve (the luminosity function). When expressed in dimensionless form (for example, as a fraction of the maximum possible luminous efficacy), this value may be called luminous efficiency of a source, overall luminous efficiency or lighting efficiency.

The main difference between the luminous efficacy of radiation and the luminous efficacy of a source is that the latter accounts for input energy that is lost as heat or otherwise exits the source as something other than electromagnetic radiation. Luminous efficacy of radiation is a property of the radiation emitted by a source. Luminous efficacy of a source is a property of the source as a whole.

Examples

The following table lists luminous efficacy of a source and efficiency for various light sources. Note that all lamps requiring electrical/electronic ballast are unless noted (see also voltage) listed without losses for that, reducing total efficiency.

Category Type Overall luminous
efficacy (lm/W) 		Overall luminous
efficiency[note 4]
Combustion Gas mantle 1–2[14] 0.15–0.3%
Incandescent 15, 40, 100 W tungsten incandescent (230 V) 8.0, 10.4, 13.8[15][16][17][18] 1.2, 1.5, 2.0%
5, 40, 100 W tungsten incandescent (120 V) 5.0, 12.6, 17.5[19] 0.7, 1.8, 2.6%
Halogen incandescent 100, 200, 500 W tungsten halogen (230 V) 16.7, 17.6, 19.8[20][18] 2.4, 2.6, 2.9%
2.6 W tungsten halogen (5.2 V) 19.2[21] 2.8%
Halogen-IR (120 V) 17.7–24.5[22] 2.6–3.5%
Tungsten quartz halogen (12–24 V) 24 3.5%
Photographic and projection lamps 35[23] 5.1%
Light-emitting diode LED screw base lamp (120 V) 102[24][25][26] 14.9%
5–16 W LED screw base lamp (230 V) 75–217[27][28][29][30] 11–32%
21.5 W LED retrofit for T8 fluorescent tube (230 V) 172[31] 25%
Theoretical limit for a white LED with phosphorescence color mixing 260–300[32] 38.1–43.9%
Arc lamp Carbon arc lamp 2–7[33] 0.29–1.0%
Xenon arc lamp 30–90[34][35][36] 4.4–13.5%
Mercury-xenon arc lamp 50–55[34] 7.3–8%
Ultra-high-pressure (UHP) mercury-vapor arc lamp, free mounted 58–78[37] 8.5–11.4%
Ultra-high-pressure (UHP) mercury-vapor arc lamp, with reflector for projectors 30–50[38] 4.4–7.3%
Fluorescent 32 W T12 tube with magnetic ballast 60[39] 9%
9–32 W compact fluorescent (with ballast) 46–75[18][40][41] 8–11.45%[42]
T8 tube with electronic ballast 80–100[39] 12–15%
PL-S 11 W U-tube, excluding ballast loss 82[43] 12%
T5 tube 70–104.2[44][45] 10–15.63%
70–150 W inductively-coupled electrodeless lighting system 71–84[46] 10–12%
Gas discharge 1400 W sulfur lamp 100[47] 15%
Metal-halide lamp 65–115[48] 9.5–17%
High-pressure sodium lamp 85–150[18] 12–22%
Low-pressure sodium lamp 100–200[18][49][50][51] 15–29%
Plasma display panel 2–10[52] 0.3–1.5%
Cathodoluminescence Electron-stimulated luminescence 30–110[53][54] 15%
Ideal sources Truncated 5800 K black-body[note 7] 251[9] 37%
Green light at 555 nm (maximum possible luminous efficacy by definition) 683.002[11][55] 100%

Sources that depend on thermal emission from a solid filament, such as incandescent light bulbs, tend to have low overall efficacy because, as explained by Donald L. Klipstein, "An ideal thermal radiator produces visible light most efficiently at temperatures around 6300 °C (6600 K or 11,500 °F). Even at this high temperature, a lot of the radiation is either infrared or ultraviolet, and the theoretical luminous [efficacy] is 95 lumens per watt. No substance is solid and usable as a light bulb filament at temperatures anywhere close to this. The surface of the sun is not quite that hot."[23] At temperatures where the tungsten filament of an ordinary light bulb remains solid (below 3683 kelvin), most of its emission is in the infrared.[23]

SI photometry units

SI photometry quantities
Quantity Unit Dimension
[nb 1] 		Notes
Name Symbol[nb 2] Name Symbol
Luminous energy Qv[nb 3] lumen second lm⋅s T⋅J The lumen second is sometimes called the talbot.
Luminous flux, luminous power Φv[nb 3] lumen (= candela steradian) lm (= cd⋅sr) J Luminous energy per unit time
Luminous intensity Iv candela (= lumen per steradian) cd (= lm/sr) J Luminous flux per unit solid angle
Luminance Lv candela per square metre cd/m2 (= lm/(sr⋅m2)) L−2⋅J Luminous flux per unit solid angle per unit projected source area. The candela per square metre is sometimes called the nit.
Illuminance Ev lux (= lumen per square metre) lx (= lm/m2) L−2⋅J Luminous flux incident on a surface
Luminous exitance, luminous emittance Mv lumen per square metre lm/m2 L−2⋅J Luminous flux emitted from a surface
Luminous exposure Hv lux second lx⋅s L−2⋅T⋅J Time-integrated illuminance
Luminous energy density ωv lumen second per cubic metre lm⋅s/m3 L−3⋅T⋅J
Luminous efficacy (of radiation) K lumen per watt lm/W M−1⋅L−2⋅T3⋅J Ratio of luminous flux to radiant flux
Luminous efficacy (of a source) η[nb 3] lumen per watt lm/W M−1⋅L−2⋅T3⋅J Ratio of luminous flux to power consumption
Luminous efficiency, luminous coefficient V 1 Luminous efficacy normalized by the maximum possible efficacy
See also:
  1. ^ The symbols in this column denote dimensions; "L", "T" and "J" are for length, time and luminous intensity respectively, not the symbols for the units litre, tesla and joule.
  2. ^ Standards organizations recommend that photometric quantities be denoted with a subscript "v" (for "visual") to avoid confusion with radiometric or photon quantities. For example: USA Standard Letter Symbols for Illuminating Engineering USAS Z7.1-1967, Y10.18-1967
  3. ^ a b c Alternative symbols sometimes seen: W for luminous energy, P or F for luminous flux, and ρ for luminous efficacy of a source.

See also

Notes

  1. ^ There are special cases of illumination involving wavelengths of light that are outside the human visible range. One example is Ultraviolet light which is not itself visible, but can excite some pigments to fluoresce, where the pigments re-emit the light into the visible range. Such special cases are not a contributing part of luminous efficacy calculations.
  2. ^ Standard vision typically perceives 555 nm as a hue of yellowish-green  , which can be emulated on an sRGB display with CSS color value rgb(120,255,0) or hex #78ff00.
  3. ^ Under standard photopic vision 507 nm is perceived as a blue-green hue similar to viridian  , however scotopic rod-only vision does not create a color sensation in the standard human vision system.
  4. ^ a b c Defined such that the maximum possible luminous efficacy corresponds to a luminous efficiency of 100%.
  5. ^ a b Black body visible spectrum
  6. ^ Most efficient source that mimics the solar spectrum within range of human visual sensitivity.
  7. ^ a b Integral of truncated Planck function times photopic luminosity function times 683.002 lm/W.
  8. ^ a b Omits the part of the spectrum where the eye's sensitivity is very poor.
  9. ^ a b Omits the part of the spectrum where the eye's sensitivity is low (≤ 5% of the peak).

References

  1. ^ Allen Stimson (1974). Photometry and Radiometry for Engineers. New York: Wiley and Son. Bibcode:1974wi...book.....S.
  2. ^ Franc Grum; Richard Becherer (1979). Optical Radiation Measurements, Vol 1. New York: Academic Press.
  3. ^ Robert Boyd (1983). Radiometry and the Detection of Optical Radiation. New York: Wiley and Son.
  4. ^ a b c International Electrotechnical Commission (IEC): International Electrotechnical Vocabulary, ref. 845-21-090, Luminous efficacy of radiation (for a specified photometric condition)
  5. ^ International Electrotechnical Commission (IEC): International Electrotechnical Vocabulary, ref. 845-21-089, Luminous efficacy (of a light source)
  6. ^ Roger A. Messenger; Jerry Ventre (2004). Photovoltaic systems engineering (2 ed.). CRC Press. p. 123. ISBN 978-0-8493-1793-4.
  7. ^ Erik Reinhard; Erum Arif Khan; Ahmet Oğuz Akyüz; Garrett Johnson (2008). Color imaging: fundamentals and applications. A K Peters, Ltd. p. 338. ISBN 978-1-56881-344-8.
  8. ^ ISO (2005). ISO 23539:2005 Photometry — The CIE system of physical photometry (Report). Retrieved 2022-01-05.
  9. ^ a b c d "Maximum Efficiency of White Light" (PDF). Retrieved 2011-07-31.
  10. ^ a b c d e Murphy, Thomas W. (2012). "Maximum spectral luminous efficacy of white light". Journal of Applied Physics. 111 (10): 104909–104909–6. arXiv:1309.7039. Bibcode:2012JAP...111j4909M. doi:10.1063/1.4721897. S2CID 6543030.
  11. ^ a b "BIPM statement: Information for users about the proposed revision of the SI" (PDF). Archived (PDF) from the original on 21 January 2018. Retrieved 5 May 2018.
  12. ^ Kohei Narisada; Duco Schreuder (2004). Light Pollution Handbook. Springer. ISBN 1-4020-2665-X.
  13. ^ Casimer DeCusatis (1998). Handbook of Applied Photometry. Springer. ISBN 1-56396-416-3.
  14. ^ Westermaier, F. V. (1920). "Recent Developments in Gas Street Lighting". The American City. 22 (5). New York: Civic Press: 490.
  15. ^ "Philips Classictone Standard 15 W clear".
  16. ^ "Philips Classictone Standard 40 W clear".
  17. ^ "Bulbs: Gluehbirne.ch: Philips Standard Lamps (German)". Bulbs.ch. Retrieved 2013-05-17.
  18. ^ a b c d e Philips Product Catalog[dead link‍] (German)
  19. ^ Keefe, T.J. (2007). "The Nature of Light". Archived from the original on 2012-01-18. Retrieved 2016-04-15.
  20. ^ "Osram halogen" (PDF). osram.de (in German). Archived from the original (PDF) on November 7, 2007. Retrieved 2008-01-28.
  21. ^ "Osram 6406330 Miniwatt-Halogen 5.2V". bulbtronics.com. Archived from the original on 2016-02-13. Retrieved 2013-04-16.
  22. ^ "GE Lighting HIR Plus Halogen PAR38s" (PDF). ge.com. Retrieved 2017-11-01.
  23. ^ a b c Klipstein, Donald L. (1996). "The Great Internet Light Bulb Book, Part I". Archived from the original on 2001-09-09. Retrieved 2006-04-16.
  24. ^ "Toshiba E-CORE LED Lamp". item.rakuten.com. Retrieved 2013-05-17.
  25. ^ "Toshiba E-CORE LED Lamp LDA5N-E17". Archived from the original on 2011-07-19.
  26. ^ Toshiba to release 93 lm/W LED bulb Ledrevie
  27. ^ "EGLO 110326 technical datasheet" (PDF). EGLO. Retrieved 2024-09-13.
  28. ^ "LED Bulb Filament A60 / E27 / 5 W (75 W) / 1 060 lm / neutral white EN | EMOS". en.b2b.emos.cz. Retrieved 2024-05-09.
  29. ^ "Philips - LED bulbs". Retrieved 2020-03-14.
  30. ^ "LED CLA 60W A60 E27 4000K CL EELA SRT4 | null". www.lighting.philips.co.uk. Retrieved 2021-09-26.
  31. ^ "MAS LEDtube 1500mm UE 21.5W 840 T8". Retrieved 2018-01-10.
  32. ^ Zyga, Lisa (2010-08-31). "White LEDs with super-high luminous efficacy could satisfy all general lighting needs". Phys.org. Retrieved 17 November 2021.
  33. ^ "Arc Lamps". Edison Tech Center. Retrieved 2015-08-20.
  34. ^ a b "Technical Information on Lamps" (PDF). Optical Building Blocks. Retrieved 2010-05-01. Note that the figure of 150 lm/W given for xenon lamps appears to be a typo. The page contains other useful information.
  35. ^ OSRAM Sylvania Lamp and Ballast Catalog. 2007.
  36. ^ "XENARC ORIGINAL D1S | OSRAM Automotive". www.osram.com. Retrieved 2021-09-30.
  37. ^ REVIEW ARTICLE: UHP lamp systems for projection applications[permanent dead link‍] Journal of Physics D: Applied Physics
  38. ^ OSRAM P-VIP PROJECTOR LAMPS Osram
  39. ^ a b Federal Energy Management Program (December 2000). "How to buy an energy-efficient fluorescent tube lamp". U.S. Department of Energy. Archived from the original on 2007-07-02. {{cite journal}}: Cite journal requires |journal= (help)
  40. ^ "Low Mercury CFLs". Energy Federation Incorporated. Archived from the original on October 13, 2008. Retrieved 2008-12-23.
  41. ^ "Conventional CFLs". Energy Federation Incorporated. Archived from the original on October 14, 2008. Retrieved 2008-12-23.
  42. ^ "Global bulbs". 1000Bulbs.com. Retrieved 2010-02-20.|
  43. ^ Phillips. "Phillips Master". Retrieved 2010-12-21.
  44. ^ Department of the Environment, Water, Heritage and the Arts, Australia. "Energy Labelling—Lamps". Archived from the original on July 23, 2008. Retrieved 2008-08-14.{{cite web}}: CS1 maint: multiple names: authors list (link)
  45. ^ "BulbAmerica.com". Bulbamerica.com. Archived from the original on December 1, 2012. Retrieved 2010-02-20.
  46. ^ SYLVANIA. "Sylvania Icetron Quicktronic Design Guide" (PDF). Retrieved 2015-06-10.
  47. ^ "1000-watt sulfur lamp now ready". IAEEL newsletter. No. 1. IAEEL. 1996. Archived from the original on 2003-08-18.
  48. ^ "The Metal Halide Advantage". Venture Lighting. 2007. Archived from the original on 2012-02-15. Retrieved 2008-08-10.
  49. ^ "LED or Neon? A scientific comparison".
  50. ^ "Why is lightning coloured? (gas excitations)". webexhibits.org.
  51. ^ Hooker, J.D. (1997). "The low-pressure sodium lamp". IEEE Conference Record - Abstracts. 1997 IEEE International Conference on Plasma Science. p. 289. doi:10.1109/PLASMA.1997.605090. ISBN 0-7803-3990-8. S2CID 102792535.
  52. ^ "Future Looks Bright for Plasma TVs" (PDF). Panasonic. 2007. Retrieved 2013-02-10.
  53. ^ "TV-Tube Technology Builds an Efficient Light Bulb". OSA. 2019. Retrieved 2020-09-12.
  54. ^ Sheshin, Evgenii P.; Kolodyazhnyj, Artem Yu.; Chadaev, Nikolai N.; Getman, Alexandr O.; Danilkin, Mikhail I.; Ozol, Dmitry I. (2019). "Prototype of cathodoluminescent lamp for general lighting using carbon fiber field emission cathode". Journal of Vacuum Science & Technology B. 37 (3). AVS: 031213. Bibcode:2019JVSTB..37c1213S. doi:10.1116/1.5070108. S2CID 155496503. Retrieved 2020-09-12.
  55. ^ Choudhury, Asim Kumar Roy (2014). "Characteristics of light sources: luminous efficacy of lamps". Principles of Colour and Appearance Measurement: Object appearance, colour perception and instrumental measurement. Vol. 1. Woodhead Publishing. p. 41. doi:10.1533/9780857099242.1. ISBN 978-0-85709-229-8. If the lamp emits all radiation at 555 nm (where Vλ = 1), the luminous efficacy will be of about 680 lm W−1, the theoretical maximum value. The lamp efficacy will be 26 and 73 lm W−1, when the whole light is emitted at 450 and 650 nm respectively. The luminous coefficient is luminous efficiency expressed as a value between zero and one, with one corresponding to an efficacy of 683 lm W−1.
Index: pl ar de en es fr it arz nl ja pt ceb sv uk vi war zh ru af ast az bg zh-min-nan bn be ca cs cy da et el eo eu fa gl ko hi hr id he ka la lv lt hu mk ms min no nn ce uz kk ro simple sk sl sr sh fi ta tt th tg azb tr ur zh-yue hy my ace als am an hyw ban bjn map-bms ba be-tarask bcl bpy bar bs br cv nv eml hif fo fy ga gd gu hak ha hsb io ig ilo ia ie os is jv kn ht ku ckb ky mrj lb lij li lmo mai mg ml zh-classical mr xmf mzn cdo mn nap new ne frr oc mhr or as pa pnb ps pms nds crh qu sa sah sco sq scn si sd szl su sw tl shn te bug vec vo wa wuu yi yo diq bat-smg zu lad kbd ang smn ab roa-rup frp arc gn av ay bh bi bo bxr cbk-zam co za dag ary se pdc dv dsb myv ext fur gv gag inh ki glk gan guw xal haw rw kbp pam csb kw km kv koi kg gom ks gcr lo lbe ltg lez nia ln jbo lg mt mi tw mwl mdf mnw nqo fj nah na nds-nl nrm nov om pi pag pap pfl pcd krc kaa ksh rm rue sm sat sc trv stq nso sn cu so srn kab roa-tara tet tpi to chr tum tk tyv udm ug vep fiu-vro vls wo xh zea ty ak bm ch ny ee ff got iu ik kl mad cr pih ami pwn pnt dz rmy rn sg st tn ss ti din chy ts kcg ve
Prefix: a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9

Portal di Ensiklopedia Dunia

Portal : Agama
Agama
Portal : Bahasa
Bahasa
Portal : Biografi
Biografi
Portal : Budaya
Budaya
Portal : Ekonomi
Ekonomi
Portal : Elektronika
Elektronika
Portal : Film
Film
Portal : Filsafat
Filsafat
Portal : Geografi
Geografi
Portal : Indonesia
Indonesia
Portal : Ilmu
Ilmu
Portal : Lingkungan
Lingkungan
Portal : Masyarakat
Masyarakat
Portal : Matematika
Matematika
Portal : Militer
Militer
Portal : Mitologi
Mitologi
Portal : Musik
Musik
Portal : Olahraga
Olahraga
Portal : Pendidikan
Pendidikan
Portal : Politik
Politik
Portal : Sastra
Sastra
Portal : Sejarah
Sejarah
Portal : Seni
Seni
Portal : Teknologi
Teknologi
Kembali kehalaman sebelumnya